Mean Well LPC-60-1400

LPC-60-1400
Импульсный блок питания 60 Вт со стабилизацией выхода по току. (LED драйвер). Iвых 1400 мА, Uвых от 9 до 42 VDC, Pвых 58.8 Вт, Uвх от 90 до 264 VAC / от 127 до 370 VDC. IP67. Технические характеристики MODEL LPC-60-1400 RATED CURRENT 1400mA DC VOLTAGE RANGE 9 ~ 42V RATE ...Читать далее

Цены

Договорная
Нет голосов


Купить

  • Описание
  • Характеристики
  • Опубликовать комментарий

Импульсный блок питания 60 Вт со стабилизацией выхода по току. (LED драйвер). Iвых 1400 мА, Uвых от 9 до 42 VDC, Pвых 58.8 Вт, Uвх от 90 до 264 VAC / от 127 до 370 VDC. IP67.

Технические характеристики

MODEL LPC-60-1400
RATED CURRENT 1400mA
DC VOLTAGE RANGE 9 ~ 42V
RATED POWER 58.8W
RIPPLE & NOISE (max.) Note.2 200mVp-p
VOLTAGE TOLERANCE Note.3 ±5.0%
CURRENT ACCURACY ±5.0%
LINE REGULATION ±1.0%
LOAD REGULATION ±2.0%
SETUP, RISE TIME Note.6 500ms, 120ms / 230VAC 500ms, 120ms / 115VAC at full load
HOLD UP TIME (Typ.) 50ms/230VAC 16ms/115VAC at full load
VOLTAGE RANGE Note.4 90 ~ 264VAC 127 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
EFFICIENCY (Typ.) 85%
AC CURRENT (Typ.) 1.2A/115VAC 0.7A/230VAC
INRUSH CURRENT(Typ.) COLD START 60A(twidth=540μs measured at 50% Ipeak) at 230VAC
MAX. No. of PSUs on 16A CIRCUIT BREAKER 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT 0.25mA / 240VAC
OVER VOLTAGE 44.1 ~ 56.7V
Protection type : Shut off o/p voltage, clamping by TVS diode
WORKING TEMP. -30 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS Ul1310, CAN/CSA C22.2 No. 223-M91(for LPC-60-1750 only), BIS IS15885(except for LPC-60-1750), EAC TP TC 004, IP67, IEC60950-1:2005+A2:2013 approved ; design refer to TUV EN60950-1
WITHSTAND VOLTAGE I/P-O/P:3KVAC
ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Compliance to EN55032 (CISPR32) Class B, EN61000-3-2 Class A, EN61000-3-3, EAC TP TC 020
EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A, EAC TP TC 020
MTBF 732Khrs min. MIL-HDBK-217F (25℃)
DIMENSION 162.5*42.5*32mm (L*W*H)
PACKING 0.4Kg; 32pcs/13.8Kg/0.63CUFT


  1. All parameters NOT specially mentioned are measuted at 230VAC input, rated load and 25°C of ambient temperature.
  2. Ripple & noise are measuted at 20MHz of bandwidth by using a 12" twisted pair—wire terminated with a 0.1uf & 47uf parallel capacitor.
  3. Tolerance: includes set up tolerance, line regulation and load regulation.
  4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
  5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performanse will be affected by the complete installation, the final equipment manufacturers must re-quality EMC Directive on the complete installation again.
  6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
  7. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.
  8. The ambient temperatute derating of 3.5°C/1000m with fanless models and of 5°C/1000m with fan models for operating altitude higher than 2000m(6500ft).
  9. For any application note and IP water proof function installation caution, please refer our user manual befote using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
  10. This product is not intended for LED applications in the EU.(ln the EU NPF/LPF/XLG series are recommended.)
  11. To fulfill requirements of latest ErP regulation for lighting luminaires, this LED Driver can only be used behind a switch without permanently connected to mains.
Вы должны зарегистрироваться или войти под своим именем, чтобы оставить комментарий