- Описание
- Характеристики
- Опубликовать комментарий
Импульсный блок питания 60 Вт со стабилизацией выхода по току. (LED драйвер). Iвых 1050 мА, Uвых от 9 до 48 VDC, Pвых 50.4 Вт, Uвх от 90 до 264 VAC / от 127 до 370 VDC. IP67.
Технические характеристики
| MODEL | LPC-60-1050 |
|---|---|
| RATED CURRENT | 1050mA |
| DC VOLTAGE RANGE | 9 ~ 48V |
| RATED POWER | 50.4W |
| RIPPLE & NOISE (max.) Note.2 | 200mVp-p |
| VOLTAGE TOLERANCE Note.3 | ±5.0% |
| CURRENT ACCURACY | ±5.0% |
| LINE REGULATION | ±1.0% |
| LOAD REGULATION | ±2.0% |
| SETUP, RISE TIME Note.6 | 500ms, 120ms / 230VAC 500ms, 120ms / 115VAC at full load |
| HOLD UP TIME (Typ.) | 50ms/230VAC 16ms/115VAC at full load |
| VOLTAGE RANGE Note.4 | 90 ~ 264VAC 127 ~ 370VDC |
| FREQUENCY RANGE | 47 ~ 63Hz |
| EFFICIENCY (Typ.) | 87% |
| AC CURRENT (Typ.) | 1.2A/115VAC 0.7A/230VAC |
| INRUSH CURRENT(Typ.) | COLD START 60A(twidth=540μs measured at 50% Ipeak) at 230VAC |
| MAX. No. of PSUs on 16A CIRCUIT BREAKER | 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC |
| LEAKAGE CURRENT | 0.25mA / 240VAC |
| OVER VOLTAGE | 50.4 ~ 60V |
| Protection type : Shut off o/p voltage, clamping by TVS diode | |
| WORKING TEMP. | -30 ~ +70℃ (Refer to "Derating Curve") |
| WORKING HUMIDITY | 20 ~ 90% RH non-condensing |
| STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH |
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) |
| VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes |
| SAFETY STANDARDS | Ul1310, CAN/CSA C22.2 No. 223-M91(for LPC-60-1750 only), BIS IS15885(except for LPC-60-1750), EAC TP TC 004, IP67, IEC60950-1:2005+A2:2013 approved ; design refer to TUV EN60950-1 |
| WITHSTAND VOLTAGE | I/P-O/P:3KVAC |
| ISOLATION RESISTANCE | I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH |
| EMC EMISSION | Compliance to EN55032 (CISPR32) Class B, EN61000-3-2 Class A, EN61000-3-3, EAC TP TC 020 |
| EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A, EAC TP TC 020 |
| MTBF | 732Khrs min. MIL-HDBK-217F (25℃) |
| DIMENSION | 162.5*42.5*32mm (L*W*H) |
| PACKING | 0.4Kg; 32pcs/13.8Kg/0.63CUFT |
- All parameters NOT specially mentioned are measuted at 230VAC input, rated load and 25°C of ambient temperature.
- Ripple & noise are measuted at 20MHz of bandwidth by using a 12" twisted pair—wire terminated with a 0.1uf & 47uf parallel capacitor.
- Tolerance: includes set up tolerance, line regulation and load regulation.
- Derating may be needed under low input voltage. Please check the static characteristics for more details.
- The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performanse will be affected by the complete installation, the final equipment manufacturers must re-quality EMC Directive on the complete installation again.
- Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
- Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.
- The ambient temperatute derating of 3.5°C/1000m with fanless models and of 5°C/1000m with fan models for operating altitude higher than 2000m(6500ft).
- For any application note and IP water proof function installation caution, please refer our user manual befote using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
- This product is not intended for LED applications in the EU.(ln the EU NPF/LPF/XLG series are recommended.)
- To fulfill requirements of latest ErP regulation for lighting luminaires, this LED Driver can only be used behind a switch without permanently connected to mains.